Defined Constants and Types for the STM32G0xx Digital-to-Analog Converter More...

Collaboration diagram for DAC Defines:

Modules
	DAC register base addresses

	DAC Registers

	DAC_CR values

	DAC_SWTRIGR Values

	DAC_DHRxxx Values

	DAC_DORx Values

	DAC_SR Values

	DAC Channel Identifier

Enumerations
enum	dac_align { DAC_ALIGN_RIGHT8 , DAC_ALIGN_RIGHT12 , DAC_ALIGN_LEFT12 }
	DAC data size (8/12 bits), alignment (right/left) More...

enum	dac_wave { DAC_WAVE_DISABLE = 0 , DAC_WAVE_NOISE = 1 , DAC_WAVE_TRIANGLE = 2 , DAC_WAVE_SAWTOOTH = 3 }
	DAC waveform generation options. More...

Functions
void	dac_enable (uint32_t dac, int channel)
	DAC Channel Enable. More...

void	dac_disable (uint32_t dac, int channel)
	DAC Channel Disable. More...

void	dac_buffer_enable (uint32_t dac, int channel)
	DAC Channel Output Buffer Enable. More...

void	dac_buffer_disable (uint32_t dac, int channel)
	DAC Channel Output Buffer Disable. More...

void	dac_dma_enable (uint32_t dac, int channel)
	DAC Channel DMA Enable. More...

void	dac_dma_disable (uint32_t dac, int channel)
	DAC Channel DMA Disable. More...

void	dac_trigger_enable (uint32_t dac, int channel)
	DAC Channel Trigger Enable. More...

void	dac_trigger_disable (uint32_t dac, int channel)
	DAC Channel Trigger Disable. More...

void	dac_set_trigger_source (uint32_t dac, uint32_t source)
	Set DAC Channel Trigger Source. More...

void	dac_set_waveform_generation (uint32_t dac, int channel, enum dac_wave wave)
	Set DAC Channel Waveform Generation mode for one or both channels. More...

void	dac_disable_waveform_generation (uint32_t dac, int channel)
	Disable DAC Channel Waveform Generation. More...

void	dac_set_waveform_characteristics (uint32_t dac, int channel, int mamp)
	Set DAC Channel LFSR Mask or Triangle Wave Amplitude. More...

void	dac_load_data_buffer_single (uint32_t dac, uint16_t data, enum dac_align align, int channel)
	Load DAC Data Register. More...

void	dac_load_data_buffer_dual (uint32_t dac, uint16_t data1, uint16_t data2, enum dac_align align)
	Load DAC Dual Data Register. More...

void	dac_software_trigger (uint32_t dac, int channel)
	Trigger the DAC by a Software Trigger. More...

Detailed Description

Defined Constants and Types for the STM32G0xx Digital-to-Analog Converter

LGPL License Terms libopencm3 License

Author: © 2012 Felix Held felix.nosp@m.-lib.nosp@m.openc.nosp@m.m3@f.nosp@m.elixh.nosp@m.eld..nosp@m.de; © 2020 Ben Brewer ben.b.nosp@m.rewe.nosp@m.r@cod.nosp@m.ethi.nosp@m.nk.co.nosp@m..uk; © 2020 Ben Brewer ben.b.nosp@m.rewe.nosp@m.r@cod.nosp@m.ethi.nosp@m.nk.co.nosp@m..uk

Enumeration Type Documentation

◆ dac_align

enum dac_align

DAC data size (8/12 bits), alignment (right/left)

Enumerator
DAC_ALIGN_RIGHT8
DAC_ALIGN_RIGHT12
DAC_ALIGN_LEFT12

Definition at line 237 of file dac_common_all.h.

◆ dac_wave

enum dac_wave

DAC waveform generation options.

Not all wave shapes are available on all parts.

Enumerator
DAC_WAVE_DISABLE
DAC_WAVE_NOISE
DAC_WAVE_TRIANGLE
DAC_WAVE_SAWTOOTH

Definition at line 246 of file dac_common_all.h.

Function Documentation

◆ dac_buffer_disable()

void dac_buffer_disable	(	uint32_t	dac,
		int	channel
	)

DAC Channel Output Buffer Disable.

Disable a digital to analog converter channel output drive buffer. Disabling this will reduce power consumption slightly and will increase the output impedance of the DAC. The buffers are enabled by default after a reset.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 66 of file dac_common_v1.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_BOFF1, and DAC_CR_BOFF2.

◆ dac_buffer_enable()

void dac_buffer_enable	(	uint32_t	dac,
		int	channel
	)

DAC Channel Output Buffer Enable.

Enable a digital to analog converter channel output drive buffer. This is an optional amplifying buffer that provides additional drive for the output signal. The buffer is enabled by default after a reset and needs to be explicitly disabled if required.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 42 of file dac_common_v1.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_BOFF1, and DAC_CR_BOFF2.

◆ dac_disable()

void dac_disable	(	uint32_t	dac,
		int	channel
	)

DAC Channel Disable.

Disable a digital to analog converter channel.

Parameters

[in]	dac	the base address of the DAC DAC register base addresses
[in]	channel	with DAC mask DAC Channel Identifier

Definition at line 159 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_EN1, and DAC_CR_EN2.

◆ dac_disable_waveform_generation()

void dac_disable_waveform_generation	(	uint32_t	dac,
		int	channel
	)

Disable DAC Channel Waveform Generation.

Note: this is equivalent to dac_set_waveform_generation (dac, channel, DAC_WAVE_DISABLE)

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 332 of file dac_common_all.c.

References dac_set_waveform_generation(), and DAC_WAVE_DISABLE.

Here is the call graph for this function:

◆ dac_dma_disable()

void dac_dma_disable	(	uint32_t	dac,
		int	channel
	)

DAC Channel DMA Disable.

Disable a digital to analog converter channel DMA mode.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 209 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_DMAEN1, and DAC_CR_DMAEN2.

◆ dac_dma_enable()

void dac_dma_enable	(	uint32_t	dac,
		int	channel
	)

DAC Channel DMA Enable.

Enable a digital to analog converter channel DMA mode (connected to DMA2 channel 3 for DAC channel 1 and DMA2 channel 4 for DAC channel 2). A DMA request is generated following an external trigger.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 185 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_DMAEN1, and DAC_CR_DMAEN2.

◆ dac_enable()

void dac_enable	(	uint32_t	dac,
		int	channel
	)

DAC Channel Enable.

Enable a digital to analog converter channel. After setting this enable, the DAC requires a t_wakeup time typically around 10 microseconds before it actually wakes up.

Parameters

[in]	dac	the base address of the DAC DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 137 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_EN1, and DAC_CR_EN2.

◆ dac_load_data_buffer_dual()

void dac_load_data_buffer_dual	(	uint32_t	dac,
		uint16_t	data1,
		uint16_t	data2,
		enum dac_align	align
	)

Load DAC Dual Data Register.

Loads the appropriate digital to analog converter dual data register with 12 or 8 bit data to be converted for both channels. This allows high bandwidth simultaneous or independent analog output. The data in both channels are aligned identically.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	data1	uint16_t for channel 1 with appropriate alignment.
[in]	data2	uint16_t for channel 2 with appropriate alignment.
[in]	align	enum dac_align. Right or left aligned, and 8 or 12 bit.

Definition at line 441 of file dac_common_all.c.

References DAC_ALIGN_LEFT12, DAC_ALIGN_RIGHT12, DAC_ALIGN_RIGHT8, DAC_DHR12LD, DAC_DHR12RD, and DAC_DHR8RD.

◆ dac_load_data_buffer_single()

void dac_load_data_buffer_single	(	uint32_t	dac,
		uint16_t	data,
		enum dac_align	align,
		int	channel
	)

Load DAC Data Register.

Loads the appropriate digital to analog converter data register with 12 or 8 bit data to be converted on a channel. The data can be aligned as follows:

right-aligned 8 bit data in bits 0-7
right-aligned 12 bit data in bits 0-11
left aligned 12 bit data in bits 4-15

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	data	uint16_t with appropriate alignment.
[in]	align	enum dac_align. Alignment and size.
[in]	channel	uint8_t with DAC mask.

Definition at line 393 of file dac_common_all.c.

References DAC_ALIGN_LEFT12, DAC_ALIGN_RIGHT12, DAC_ALIGN_RIGHT8, DAC_CHANNEL1, DAC_CHANNEL2, DAC_DHR12L1, DAC_DHR12L2, DAC_DHR12R1, DAC_DHR12R2, DAC_DHR8R1, and DAC_DHR8R2.

◆ dac_set_trigger_source()

void dac_set_trigger_source	(	uint32_t	dac,
		uint32_t	source
	)

Set DAC Channel Trigger Source.

Sets the digital to analog converter trigger source, which can be taken from various timers, an external trigger or a software trigger.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	source	Taken from DAC Channel 2 Trigger Source Selection or DAC Channel 1 Trigger Source Selection or a logical OR of one of each of these to set both channels simultaneously.

Definition at line 287 of file dac_common_all.c.

References DAC_CR.

◆ dac_set_waveform_characteristics()

void dac_set_waveform_characteristics	(	uint32_t	dac,
		int	channel,
		int	mamp
	)

Set DAC Channel LFSR Mask or Triangle Wave Amplitude.

Sets the digital to analog converter superimposed waveform generation characteristics.

If the noise generation mode is set, this sets the length of the PRBS sequence and hence the amplitude of the output noise signal. Default setting is length 1.
If the triangle wave generation mode is set, this sets the amplitude of the output signal as 2^(n)-1 where n is the parameter value. Default setting is 1.

Note: High amplitude levels of these waveforms can overload the DAC and distort the signal output.; This must be called before enabling the DAC as the settings will then become read-only.; The DAC trigger must be enabled for this to work.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	one or both, select from DAC Channel Identifier
[in]	mamp	amplitude of mixed waveform, bit width DAC_CR_MAMPx_MASK

Definition at line 356 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_MAMP1_SHIFT, DAC_CR_MAMP2_SHIFT, and DAC_CR_MAMPx_MASK.

◆ dac_set_waveform_generation()

void dac_set_waveform_generation	(	uint32_t	dac,
		int	channel,
		enum dac_wave	wave
	)

Set DAC Channel Waveform Generation mode for one or both channels.

These signals are superimposed on existing output values in the DAC output registers. Waveform can be disabled, noise, triangular, or sawtooth, depending on family.

Note: The DAC trigger must be enabled for this to work.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	one or both, DAC Channel Identifier
[in]	wave	enum dac_wave. mode for channel

Definition at line 302 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_WAVE1_SHIFT, DAC_CR_WAVE2_SHIFT, and DAC_CR_WAVEx_MASK.

Referenced by dac_disable_waveform_generation().

Here is the caller graph for this function:

◆ dac_software_trigger()

void dac_software_trigger	(	uint32_t	dac,
		int	channel
	)

Trigger the DAC by a Software Trigger.

If the trigger source is set to be a software trigger, cause a trigger to occur. The trigger is cleared by hardware after conversion.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 470 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_SWTRIGR, DAC_SWTRIGR_SWTRIG1, and DAC_SWTRIGR_SWTRIG2.

◆ dac_trigger_disable()

void dac_trigger_disable	(	uint32_t	dac,
		int	channel
	)

DAC Channel Trigger Disable.

Disable a digital to analog converter channel external trigger.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 260 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_TEN1, and DAC_CR_TEN2.

◆ dac_trigger_enable()

void dac_trigger_enable	(	uint32_t	dac,
		int	channel
	)

DAC Channel Trigger Enable.

Enable a digital to analog converter channel external trigger mode. This allows an external trigger to initiate register transfers from the buffer register to the DAC output register, followed by a DMA transfer to the buffer register if DMA is enabled. The trigger source must also be selected.

Parameters

[in]	dac	the base address of the DAC. DAC register base addresses
[in]	channel	with DAC mask. DAC Channel Identifier

Definition at line 236 of file dac_common_all.c.

References DAC_CHANNEL1, DAC_CHANNEL2, DAC_CHANNEL_BOTH, DAC_CR, DAC_CR_TEN1, and DAC_CR_TEN2.

Modules

Enumerations

Functions

Detailed Description

Enumeration Type Documentation

◆ dac_align

◆ dac_wave

Function Documentation

◆ dac_buffer_disable()

◆ dac_buffer_enable()

◆ dac_disable()

◆ dac_disable_waveform_generation()

◆ dac_dma_disable()

◆ dac_dma_enable()

◆ dac_enable()

◆ dac_load_data_buffer_dual()

◆ dac_load_data_buffer_single()

◆ dac_set_trigger_source()

◆ dac_set_waveform_characteristics()

◆ dac_set_waveform_generation()

◆ dac_software_trigger()

◆ dac_trigger_disable()

◆ dac_trigger_enable()