libopencm3
A free/libre/open-source firmware library for various ARM Cortex-M3 microcontrollers.
ADC peripheral API
Collaboration diagram for ADC peripheral API:

Functions

void adc_set_clk_source (uint32_t adc, uint32_t source)
 ADC Set Clock Source. More...
 
void adc_set_clk_prescale (uint32_t adc, uint32_t prescale)
 ADC Set Clock Prescale. More...
 
void adc_set_sample_time_on_all_channels (uint32_t adc, uint8_t time)
 ADC Set the Sample Time for All Channels. More...
 
void adc_set_channel_sample_time_selection (uint32_t adc, uint8_t channel, uint8_t selection)
 ADC Set the Sample Time Selection for a Single Channel. More...
 
void adc_set_selection_sample_time (uint32_t adc, uint8_t selection, uint8_t time)
 ADC Set the Sample Time for Given Selection. More...
 
void adc_set_regular_sequence (uint32_t adc, uint8_t length, uint8_t channel[])
 ADC Set a Regular Channel Conversion Sequence. More...
 
void adc_enable_regulator (uint32_t adc)
 Enable the ADC Voltage regulator. More...
 
void adc_disable_regulator (uint32_t adc)
 Disable the ADC Voltage regulator. More...
 
bool adc_eoc (uint32_t adc)
 ADC Read the End-of-Conversion Flag. More...
 
bool adc_eos (uint32_t adc)
 ADC Read the End-of-Sequence Flag for Regular Conversions. More...
 
void adc_power_on_async (uint32_t adc)
 Turn on the ADC (async) More...
 
bool adc_is_power_on (uint32_t adc)
 Is the ADC powered up and ready? More...
 
void adc_power_on (uint32_t adc)
 Turn on the ADC. More...
 
void adc_power_off_async (uint32_t adc)
 Turn off the ADC (async) This will actually block if it needs to turn off a currently running conversion, as per ref man. More...
 
bool adc_is_power_off (uint32_t adc)
 Is the ADC powered down? More...
 
void adc_power_off (uint32_t adc)
 Turn off the ADC This will actually block if it needs to turn off a currently running conversion, as per ref man. More...
 
void adc_calibrate_async (uint32_t adc)
 Start the ADC calibration and immediately return. More...
 
bool adc_is_calibrating (uint32_t adc)
 Is the ADC Calibrating? More...
 
void adc_calibrate (uint32_t adc)
 Start ADC calibration and wait for it to finish. More...
 
void adc_set_continuous_conversion_mode (uint32_t adc)
 Enable Continuous Conversion Mode In this mode the ADC starts a new conversion of a single channel or a channel group immediately following completion of the previous channel group conversion. More...
 
void adc_set_single_conversion_mode (uint32_t adc)
 Enable Single Conversion Mode In this mode the ADC performs a conversion of one channel or a channel group and stops. More...
 
void adc_set_resolution (uint32_t adc, uint16_t resolution)
 ADC Set Resolution. More...
 
void adc_set_left_aligned (uint32_t adc)
 ADC Set the Data as Left Aligned. More...
 
void adc_set_right_aligned (uint32_t adc)
 ADC Set the Data as Right Aligned. More...
 
void adc_enable_dma (uint32_t adc)
 ADC Enable DMA Transfers. More...
 
void adc_disable_dma (uint32_t adc)
 ADC Disable DMA Transfers. More...
 
void adc_enable_overrun_interrupt (uint32_t adc)
 ADC Enable the Overrun Interrupt. More...
 
void adc_disable_overrun_interrupt (uint32_t adc)
 ADC Disable the Overrun Interrupt. More...
 
bool adc_get_overrun_flag (uint32_t adc)
 ADC Read the Overrun Flag. More...
 
void adc_clear_overrun_flag (uint32_t adc)
 ADC Clear Overrun Flags. More...
 
void adc_enable_eoc_interrupt (uint32_t adc)
 ADC Enable Regular End-Of-Conversion Interrupt. More...
 
void adc_disable_eoc_interrupt (uint32_t adc)
 ADC Disable Regular End-Of-Conversion Interrupt. More...
 
uint32_t adc_read_regular (uint32_t adc)
 ADC Read from the Regular Conversion Result Register. More...
 
void adc_enable_temperature_sensor (void)
 Enable the temperature sensor (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is. More...
 
void adc_disable_temperature_sensor (void)
 Disable the temperature sensor (only) More...
 
void adc_enable_vrefint (void)
 Enable the internal voltage reference (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is. More...
 
void adc_disable_vrefint (void)
 Disable the internal voltage reference (only) More...
 
void adc_start_conversion_regular (uint32_t adc)
 ADC Software Triggered Conversion on Regular Channels. More...
 
void adc_enable_dma_circular_mode (uint32_t adc)
 Enable circular mode for DMA transfers. More...
 
void adc_disable_dma_circular_mode (uint32_t adc)
 Disable circular mode for DMA transfers. More...
 
void adc_enable_delayed_conversion_mode (uint32_t adc)
 Enable Delayed Conversion Mode. More...
 
void adc_disable_delayed_conversion_mode (uint32_t adc)
 Enable Delayed Conversion Mode. More...
 

Detailed Description

Author
© 2019 Guillaume Revaillot g.rev.nosp@m.aill.nosp@m.ot@gm.nosp@m.ail..nosp@m.com
Date
10 January 2019

LGPL License Terms libopencm3 License

Author
© 2015 Karl Palsson karlp.nosp@m.@twe.nosp@m.ak.ne.nosp@m.t.au

This library supports one style of the Analog to Digital Conversion System in the STM32 series of ARM Cortex Microcontrollers by ST Microelectronics.

The style of ADC Peripheral supported by this code is found in the F0, L0 and F30x series devices (at the time of writing)

LGPL License Terms libopencm3 License

Function Documentation

◆ adc_calibrate()

void adc_calibrate ( uint32_t  adc)

Start ADC calibration and wait for it to finish.

Parameters
adcADC Block register address base ADC register base addresses

Definition at line 175 of file adc_common_v2.c.

References adc_calibrate_async(), and adc_is_calibrating().

Here is the call graph for this function:

◆ adc_calibrate_async()

void adc_calibrate_async ( uint32_t  adc)

Start the ADC calibration and immediately return.

See also
adc_calibrate
adc_is_calibrating
Parameters
adcADC Block register address base ADC register base addresses

Definition at line 156 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADCAL.

Referenced by adc_calibrate().

Here is the caller graph for this function:

◆ adc_clear_overrun_flag()

void adc_clear_overrun_flag ( uint32_t  adc)

ADC Clear Overrun Flags.

The overrun flag is cleared. Note that if an overrun occurs, DMA is terminated. The flag must be cleared and the DMA stream and ADC reinitialised to resume conversions (see the reference manual).

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 299 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_OVR.

◆ adc_disable_delayed_conversion_mode()

void adc_disable_delayed_conversion_mode ( uint32_t  adc)

Enable Delayed Conversion Mode.

Parameters
[in]adcADC block register address base ADC register base addresses

Definition at line 425 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_disable_dma()

void adc_disable_dma ( uint32_t  adc)

ADC Disable DMA Transfers.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 250 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_disable_dma_circular_mode()

void adc_disable_dma_circular_mode ( uint32_t  adc)

Disable circular mode for DMA transfers.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 407 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_disable_eoc_interrupt()

void adc_disable_eoc_interrupt ( uint32_t  adc)

ADC Disable Regular End-Of-Conversion Interrupt.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 317 of file adc_common_v2.c.

References ADC_IER.

◆ adc_disable_overrun_interrupt()

void adc_disable_overrun_interrupt ( uint32_t  adc)

ADC Disable the Overrun Interrupt.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 272 of file adc_common_v2.c.

References ADC_IER.

◆ adc_disable_regulator()

void adc_disable_regulator ( uint32_t  adc)

Disable the ADC Voltage regulator.

Parameters
[in]adcADC base address (ADC register base addresses)

Definition at line 201 of file adc.c.

References ADC_CR.

◆ adc_disable_temperature_sensor()

void adc_disable_temperature_sensor ( void  )

Disable the temperature sensor (only)

See also
adc_enable_temperature_sensor

Definition at line 351 of file adc_common_v2.c.

References ADC1, and ADC_CCR.

◆ adc_disable_vrefint()

void adc_disable_vrefint ( void  )

Disable the internal voltage reference (only)

See also
adc_enable_vrefint

Definition at line 372 of file adc_common_v2.c.

References ADC1, and ADC_CCR.

◆ adc_enable_delayed_conversion_mode()

void adc_enable_delayed_conversion_mode ( uint32_t  adc)

Enable Delayed Conversion Mode.

Parameters
[in]adcADC block register address base ADC register base addresses

Definition at line 416 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_AUTDLY.

◆ adc_enable_dma()

void adc_enable_dma ( uint32_t  adc)

ADC Enable DMA Transfers.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 241 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_DMAEN.

◆ adc_enable_dma_circular_mode()

void adc_enable_dma_circular_mode ( uint32_t  adc)

Enable circular mode for DMA transfers.

For this to work it needs to be ebabled on the DMA side as well.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 398 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_DMACFG.

◆ adc_enable_eoc_interrupt()

void adc_enable_eoc_interrupt ( uint32_t  adc)

ADC Enable Regular End-Of-Conversion Interrupt.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 308 of file adc_common_v2.c.

References ADC_IER, and ADC_IER_EOCIE.

◆ adc_enable_overrun_interrupt()

void adc_enable_overrun_interrupt ( uint32_t  adc)

ADC Enable the Overrun Interrupt.

The overrun interrupt is generated when data is not read from a result register before the next conversion is written. If DMA is enabled, all transfers are terminated and any conversion sequence is aborted.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 263 of file adc_common_v2.c.

References ADC_IER, and ADC_IER_OVRIE.

◆ adc_enable_regulator()

void adc_enable_regulator ( uint32_t  adc)

Enable the ADC Voltage regulator.

Parameters
[in]adcADC base address (ADC register base addresses)

Definition at line 191 of file adc.c.

References ADC_CR, and ADC_CR_ADVREGEN.

◆ adc_enable_temperature_sensor()

void adc_enable_temperature_sensor ( void  )

Enable the temperature sensor (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is.

See also
adc_disable_temperature_sensor

Definition at line 342 of file adc_common_v2.c.

References ADC1, ADC_CCR, and ADC_CCR_TSEN.

◆ adc_enable_vrefint()

void adc_enable_vrefint ( void  )

Enable the internal voltage reference (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is.

FIXME - on f3, you can actually have it on ADC34 as well!

See also
adc_disable_vrefint

Definition at line 363 of file adc_common_v2.c.

References ADC1, ADC_CCR, and ADC_CCR_VREFEN.

◆ adc_eoc()

bool adc_eoc ( uint32_t  adc)

ADC Read the End-of-Conversion Flag.

This flag is set by hardware at the end of each regular conversion of a channel when a new data is available in the ADCx_DR register.

Parameters
[in]adcUnsigned int32. ADC block register address base ADC register base addresses
Returns
bool. End of conversion flag.

Definition at line 49 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_EOC.

◆ adc_eos()

bool adc_eos ( uint32_t  adc)

ADC Read the End-of-Sequence Flag for Regular Conversions.

This flag is set after all channels of an regular group have been converted.

Parameters
[in]adcUnsigned int32. ADC block register address base ADC register base addresses
Returns
bool. End of conversion flag.

Definition at line 63 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_EOS.

◆ adc_get_overrun_flag()

bool adc_get_overrun_flag ( uint32_t  adc)

ADC Read the Overrun Flag.

The overrun flag is set when data is not read from a result register before the next conversion is written. If DMA is enabled, all transfers are terminated and any conversion sequence is aborted.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 285 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_OVR.

◆ adc_is_calibrating()

bool adc_is_calibrating ( uint32_t  adc)

Is the ADC Calibrating?

Parameters
adcADC Block register address base ADC register base addresses
Returns
true if the adc is currently calibrating

Definition at line 166 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADCAL.

Referenced by adc_calibrate().

Here is the caller graph for this function:

◆ adc_is_power_off()

bool adc_is_power_off ( uint32_t  adc)

Is the ADC powered down?

See also
adc_power_off_async
Parameters
adcADC Block register address base ADC register base addresses

Definition at line 132 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADEN.

Referenced by adc_power_off(), and adc_power_off_async().

Here is the caller graph for this function:

◆ adc_is_power_on()

bool adc_is_power_on ( uint32_t  adc)

Is the ADC powered up and ready?

See also
adc_power_on_async
Parameters
adcADC Block register address base ADC register base addresses
Returns
true if adc is ready for use

Definition at line 84 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_ADRDY.

Referenced by adc_power_on().

Here is the caller graph for this function:

◆ adc_power_off()

void adc_power_off ( uint32_t  adc)

Turn off the ADC This will actually block if it needs to turn off a currently running conversion, as per ref man.

See also
adc_power_off_async
Parameters
adcADC Block register address base ADC register base addresses

Definition at line 144 of file adc_common_v2.c.

References adc_is_power_off(), and adc_power_off_async().

Here is the call graph for this function:

◆ adc_power_off_async()

void adc_power_off_async ( uint32_t  adc)

Turn off the ADC (async) This will actually block if it needs to turn off a currently running conversion, as per ref man.

(Handles injected on hardware that supports injected conversions.

See also
adc_wait_power_off
Parameters
adcADC Block register address base ADC register base addresses

Definition at line 108 of file adc_common_v2.c.

References ADC_CR, ADC_CR_ADDIS, ADC_CR_ADSTART, ADC_CR_ADSTP, and adc_is_power_off().

Referenced by adc_power_off().

Here is the call graph for this function:
Here is the caller graph for this function:

◆ adc_power_on()

void adc_power_on ( uint32_t  adc)

Turn on the ADC.

See also
adc_power_on_async
Parameters
adcADC Block register address base ADC register base addresses

Definition at line 94 of file adc_common_v2.c.

References adc_is_power_on(), and adc_power_on_async().

Here is the call graph for this function:

◆ adc_power_on_async()

void adc_power_on_async ( uint32_t  adc)

Turn on the ADC (async)

See also
adc_wait_power_on
Parameters
adcADC Block register address base ADC register base addresses

Definition at line 73 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADEN.

Referenced by adc_power_on().

Here is the caller graph for this function:

◆ adc_read_regular()

uint32_t adc_read_regular ( uint32_t  adc)

ADC Read from the Regular Conversion Result Register.

The result read back is 12 bits, right or left aligned within the first 16 bits.

Parameters
[in]adcUnsigned int32. ADC block register address base ADC register base addresses
Returns
Unsigned int32 conversion result.

Definition at line 331 of file adc_common_v2.c.

References ADC_DR.

◆ adc_set_channel_sample_time_selection()

void adc_set_channel_sample_time_selection ( uint32_t  adc,
uint8_t  channel,
uint8_t  selection 
)

ADC Set the Sample Time Selection for a Single Channel.

Parameters
[in]adcADC base address (ADC register base addresses)
[in]channelADC Channel (0..18 or ADC Channel Numbers)
[in]selectionSampling time selection (ADC Sample Time selection)

Definition at line 84 of file adc.c.

References ADC_SMPR1, ADC_SMPR_SMPSEL_CHANNEL_MASK, and ADC_SMPR_SMPSEL_CHANNEL_SHIFT.

◆ adc_set_clk_prescale()

void adc_set_clk_prescale ( uint32_t  adc,
uint32_t  prescale 
)

ADC Set Clock Prescale.

Parameters
[in]adcADC base address (ADC register base addresses)
[in]prescalePrescale value for ADC Async Clock (ADC clock prescaler)

Definition at line 51 of file adc.c.

References ADC_CCR, ADC_CCR_PRESC_MASK, and ADC_CCR_PRESC_SHIFT.

◆ adc_set_clk_source()

void adc_set_clk_source ( uint32_t  adc,
uint32_t  source 
)

ADC Set Clock Source.

Parameters
[in]adcADC base address (ADC register base addresses)
[in]sourceSource (ADC Clock mode)

Definition at line 38 of file adc.c.

References ADC_CFGR2, ADC_CFGR2_CKMODE_MASK, and ADC_CFGR2_CKMODE_SHIFT.

◆ adc_set_continuous_conversion_mode()

void adc_set_continuous_conversion_mode ( uint32_t  adc)

Enable Continuous Conversion Mode In this mode the ADC starts a new conversion of a single channel or a channel group immediately following completion of the previous channel group conversion.

Parameters
[in]adcADC block register address base ADC register base addresses

Definition at line 189 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_CONT.

◆ adc_set_left_aligned()

void adc_set_left_aligned ( uint32_t  adc)

ADC Set the Data as Left Aligned.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 223 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_ALIGN.

◆ adc_set_regular_sequence()

void adc_set_regular_sequence ( uint32_t  adc,
uint8_t  length,
uint8_t  channel[] 
)

ADC Set a Regular Channel Conversion Sequence.

Define a simple sequence of channels to be converted. ADCSTART must be de-asserted before sequence setup.

Parameters
[in]adcADC base address (ADC register base addresses)
[in]lengthNumber of channels in the group, range 0..18
[in]channelSet of channels in sequence (0..18 or ADC Channel Numbers)

Definition at line 127 of file adc.c.

References ADC_CFGR1, ADC_CFGR1_CHSELRMOD, ADC_CFGR1_SCANDIR, ADC_CHSELR, ADC_CHSELR_CHSEL, ADC_CHSELR_MAX_CHANNELS, ADC_ISR, ADC_ISR_CCRDY, and cm3_assert_not_reached.

◆ adc_set_resolution()

void adc_set_resolution ( uint32_t  adc,
uint16_t  resolution 
)

ADC Set Resolution.

ADC Resolution can be reduced from 12 bits to 10, 8 or 6 bits for a corresponding reduction in conversion time.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)
[in]resolutionUnsigned int16. Resolution value (adc_api_res)

Definition at line 214 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_set_right_aligned()

void adc_set_right_aligned ( uint32_t  adc)

ADC Set the Data as Right Aligned.

Parameters
[in]adcUnsigned int32. ADC base address (ADC register base addresses)

Definition at line 232 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_set_sample_time_on_all_channels()

void adc_set_sample_time_on_all_channels ( uint32_t  adc,
uint8_t  time 
)

ADC Set the Sample Time for All Channels.

Setup all ADC channels to use a single ADC sampling time.

Parameters
[in]adcADC base address (ADC register base addresses)
[in]timeADC Sampling Time (ADC Sampling Time)

Definition at line 66 of file adc.c.

References ADC_SMPR1, ADC_SMPR_SMP1_MASK, ADC_SMPR_SMP1_SHIFT, ADC_SMPR_SMPSEL_MASK, and ADC_SMPR_SMPSEL_SHIFT.

◆ adc_set_selection_sample_time()

void adc_set_selection_sample_time ( uint32_t  adc,
uint8_t  selection,
uint8_t  time 
)

ADC Set the Sample Time for Given Selection.

Parameters
[in]adcADC base address (ADC register base addresses)
[in]selectionSampling Time Selection (ADC Sample Time selection)
[in]timeSampling Time (ADC Sample Time selection values)

Definition at line 100 of file adc.c.

References ADC_SMPR1, ADC_SMPR_SMP1_MASK, ADC_SMPR_SMP1_SHIFT, ADC_SMPR_SMP2_MASK, ADC_SMPR_SMP2_SHIFT, ADC_SMPR_SMPSEL_SMP1, and ADC_SMPR_SMPSEL_SMP2.

◆ adc_set_single_conversion_mode()

void adc_set_single_conversion_mode ( uint32_t  adc)

Enable Single Conversion Mode In this mode the ADC performs a conversion of one channel or a channel group and stops.

Parameters
[in]adcADC block register address base ADC register base addresses

Definition at line 201 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_start_conversion_regular()

void adc_start_conversion_regular ( uint32_t  adc)

ADC Software Triggered Conversion on Regular Channels.

This starts conversion on a set of defined regular channels. Depending on the configuration bits EXTEN, a conversion will start immediately (software trigger configuration) or once a regular hardware trigger event occurs (hardware trigger configuration)

Parameters
[in]adcADC block register address base ADC register base addresses

Definition at line 386 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADSTART.