Defined Constants and Types for the STM32F0xx Analog to Digital Converter More...

Collaboration diagram for ADC Defines:

Modules
	ADC register base addresses

	ADC resolutions

	ADC sampling time

	ADC clock source

	ADC Channel Numbers

	ADC Operation Modes
	ADC Result API.

	ADC registers

	ISR ADC interrupt status register

	IER ADC interrupt enable register

	CR ADC control register

	CFGR1 ADC configuration register 1

	SMPR ADC sample time register

	CFGR2 ADC configuration register 2

	TR1 ADC watchdog threshold register 1

	CCR ADC common configuration register

	CHSELR ADC Channel Selection register

Functions
void	adc_power_on_async (uint32_t adc)
	Turn on the ADC (async) More...

void	adc_power_on (uint32_t adc)
	Turn on the ADC. More...

bool	adc_is_power_on (uint32_t adc)
	Is the ADC powered up and ready? More...

void	adc_power_off_async (uint32_t adc)
	Turn off the ADC (async) This will actually block if it needs to turn off a currently running conversion, as per ref man. More...

void	adc_power_off (uint32_t adc)
	Turn off the ADC This will actually block if it needs to turn off a currently running conversion, as per ref man. More...

bool	adc_is_power_off (uint32_t adc)
	Is the ADC powered down? More...

void	adc_calibrate_async (uint32_t adc)
	Start the ADC calibration and immediately return. More...

bool	adc_is_calibrating (uint32_t adc)
	Is the ADC Calibrating? More...

void	adc_calibrate (uint32_t adc)
	Start ADC calibration and wait for it to finish. More...

void	adc_set_continuous_conversion_mode (uint32_t adc)
	Enable Continuous Conversion Mode In this mode the ADC starts a new conversion of a single channel or a channel group immediately following completion of the previous channel group conversion. More...

void	adc_set_single_conversion_mode (uint32_t adc)
	Enable Single Conversion Mode In this mode the ADC performs a conversion of one channel or a channel group and stops. More...

void	adc_set_regular_sequence (uint32_t adc, uint8_t length, uint8_t channel[])
	ADC Set a Regular Channel Conversion Sequence. More...

void	adc_set_sample_time_on_all_channels (uint32_t adc, uint8_t time)
	ADC Set the Sample Time for All Channels. More...

void	adc_enable_temperature_sensor (void)
	Enable the temperature sensor (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is. More...

void	adc_disable_temperature_sensor (void)
	Disable the temperature sensor (only) More...

void	adc_enable_vrefint (void)
	Enable the internal voltage reference (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is. More...

void	adc_disable_vrefint (void)
	Disable the internal voltage reference (only) More...

void	adc_set_resolution (uint32_t adc, uint16_t resolution)
	ADC Set Resolution. More...

void	adc_set_left_aligned (uint32_t adc)
	ADC Set the Data as Left Aligned. More...

void	adc_set_right_aligned (uint32_t adc)
	ADC Set the Data as Right Aligned. More...

void	adc_enable_dma (uint32_t adc)
	ADC Enable DMA Transfers. More...

void	adc_disable_dma (uint32_t adc)
	ADC Disable DMA Transfers. More...

bool	adc_eoc (uint32_t adc)
	ADC Read the End-of-Conversion Flag. More...

bool	adc_eos (uint32_t adc)
	ADC Read the End-of-Sequence Flag for Regular Conversions. More...

void	adc_enable_eoc_interrupt (uint32_t adc)
	ADC Enable Regular End-Of-Conversion Interrupt. More...

void	adc_disable_eoc_interrupt (uint32_t adc)
	ADC Disable Regular End-Of-Conversion Interrupt. More...

void	adc_enable_overrun_interrupt (uint32_t adc)
	ADC Enable the Overrun Interrupt. More...

void	adc_disable_overrun_interrupt (uint32_t adc)
	ADC Disable the Overrun Interrupt. More...

bool	adc_get_overrun_flag (uint32_t adc)
	ADC Read the Overrun Flag. More...

void	adc_clear_overrun_flag (uint32_t adc)
	ADC Clear Overrun Flags. More...

uint32_t	adc_read_regular (uint32_t adc)
	ADC Read from the Regular Conversion Result Register. More...

void	adc_start_conversion_regular (uint32_t adc)
	ADC Software Triggered Conversion on Regular Channels. More...

void	adc_enable_dma_circular_mode (uint32_t adc)
	Enable circular mode for DMA transfers. More...

void	adc_disable_dma_circular_mode (uint32_t adc)
	Disable circular mode for DMA transfers. More...

void	adc_enable_delayed_conversion_mode (uint32_t adc)
	Enable Delayed Conversion Mode. More...

void	adc_disable_delayed_conversion_mode (uint32_t adc)
	Enable Delayed Conversion Mode. More...

Detailed Description

Defined Constants and Types for the STM32F0xx Analog to Digital Converter

Version: 1.0.0

Date: 11 July 2013

LGPL License Terms libopencm3 License

Author: © 2015 Karl Palsson karlp.nosp@m.@twe.nosp@m.ak.ne.nosp@m.t.au

Function Documentation

◆ adc_calibrate()

void adc_calibrate ( uint32_t adc )

Start ADC calibration and wait for it to finish.

Parameters

adc	ADC Block register address base ADC register base addresses

Definition at line 175 of file adc_common_v2.c.

References adc_calibrate_async(), and adc_is_calibrating().

Here is the call graph for this function:

◆ adc_calibrate_async()

void adc_calibrate_async ( uint32_t adc )

Start the ADC calibration and immediately return.

See also: adc_calibrate; adc_is_calibrating

Parameters

adc	ADC Block register address base ADC register base addresses

Definition at line 156 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADCAL.

Referenced by adc_calibrate().

Here is the caller graph for this function:

◆ adc_clear_overrun_flag()

void adc_clear_overrun_flag ( uint32_t adc )

ADC Clear Overrun Flags.

The overrun flag is cleared. Note that if an overrun occurs, DMA is terminated. The flag must be cleared and the DMA stream and ADC reinitialised to resume conversions (see the reference manual).

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 299 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_OVR.

◆ adc_disable_delayed_conversion_mode()

void adc_disable_delayed_conversion_mode ( uint32_t adc )

Enable Delayed Conversion Mode.

Parameters

[in] adc ADC block register address base ADC register base addresses

Definition at line 425 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_disable_dma()

void adc_disable_dma ( uint32_t adc )

ADC Disable DMA Transfers.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 250 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_disable_dma_circular_mode()

void adc_disable_dma_circular_mode ( uint32_t adc )

Disable circular mode for DMA transfers.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 407 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_disable_eoc_interrupt()

void adc_disable_eoc_interrupt ( uint32_t adc )

ADC Disable Regular End-Of-Conversion Interrupt.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 317 of file adc_common_v2.c.

References ADC_IER.

◆ adc_disable_overrun_interrupt()

void adc_disable_overrun_interrupt ( uint32_t adc )

ADC Disable the Overrun Interrupt.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 272 of file adc_common_v2.c.

References ADC_IER.

◆ adc_disable_temperature_sensor()

void adc_disable_temperature_sensor ( void )

Disable the temperature sensor (only)

See also: adc_enable_temperature_sensor

Definition at line 351 of file adc_common_v2.c.

References ADC1, and ADC_CCR.

◆ adc_disable_vrefint()

void adc_disable_vrefint ( void )

Disable the internal voltage reference (only)

See also: adc_enable_vrefint

Definition at line 372 of file adc_common_v2.c.

References ADC1, and ADC_CCR.

◆ adc_enable_delayed_conversion_mode()

void adc_enable_delayed_conversion_mode ( uint32_t adc )

Enable Delayed Conversion Mode.

Parameters

[in] adc ADC block register address base ADC register base addresses

Definition at line 416 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_AUTDLY.

◆ adc_enable_dma()

void adc_enable_dma ( uint32_t adc )

ADC Enable DMA Transfers.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 241 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_DMAEN.

◆ adc_enable_dma_circular_mode()

void adc_enable_dma_circular_mode ( uint32_t adc )

Enable circular mode for DMA transfers.

For this to work it needs to be ebabled on the DMA side as well.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 398 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_DMACFG.

◆ adc_enable_eoc_interrupt()

void adc_enable_eoc_interrupt ( uint32_t adc )

ADC Enable Regular End-Of-Conversion Interrupt.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 308 of file adc_common_v2.c.

References ADC_IER, and ADC_IER_EOCIE.

◆ adc_enable_overrun_interrupt()

void adc_enable_overrun_interrupt ( uint32_t adc )

ADC Enable the Overrun Interrupt.

The overrun interrupt is generated when data is not read from a result register before the next conversion is written. If DMA is enabled, all transfers are terminated and any conversion sequence is aborted.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 263 of file adc_common_v2.c.

References ADC_IER, and ADC_IER_OVRIE.

◆ adc_enable_temperature_sensor()

void adc_enable_temperature_sensor ( void )

Enable the temperature sensor (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is.

See also: adc_disable_temperature_sensor

Definition at line 342 of file adc_common_v2.c.

References ADC1, ADC_CCR, and ADC_CCR_TSEN.

◆ adc_enable_vrefint()

void adc_enable_vrefint ( void )

Enable the internal voltage reference (only) The channel this is available on is unfortunately not consistent, even though the bit used to enable it is.

FIXME - on f3, you can actually have it on ADC34 as well!

See also: adc_disable_vrefint

Definition at line 363 of file adc_common_v2.c.

References ADC1, ADC_CCR, and ADC_CCR_VREFEN.

◆ adc_eoc()

bool adc_eoc ( uint32_t adc )

ADC Read the End-of-Conversion Flag.

This flag is set by hardware at the end of each regular conversion of a channel when a new data is available in the ADCx_DR register.

Parameters

[in] adc Unsigned int32. ADC block register address base ADC register base addresses

Returns: bool. End of conversion flag.

Definition at line 49 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_EOC.

◆ adc_eos()

bool adc_eos ( uint32_t adc )

ADC Read the End-of-Sequence Flag for Regular Conversions.

This flag is set after all channels of an regular group have been converted.

Parameters

[in] adc Unsigned int32. ADC block register address base ADC register base addresses

Returns: bool. End of conversion flag.

Definition at line 63 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_EOS.

◆ adc_get_overrun_flag()

bool adc_get_overrun_flag ( uint32_t adc )

ADC Read the Overrun Flag.

The overrun flag is set when data is not read from a result register before the next conversion is written. If DMA is enabled, all transfers are terminated and any conversion sequence is aborted.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 285 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_OVR.

◆ adc_is_calibrating()

bool adc_is_calibrating ( uint32_t adc )

Is the ADC Calibrating?

Parameters

adc	ADC Block register address base ADC register base addresses

Returns: true if the adc is currently calibrating

Definition at line 166 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADCAL.

Referenced by adc_calibrate().

Here is the caller graph for this function:

◆ adc_is_power_off()

bool adc_is_power_off ( uint32_t adc )

Is the ADC powered down?

See also: adc_power_off_async

Parameters

adc	ADC Block register address base ADC register base addresses

Definition at line 132 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADEN.

Referenced by adc_power_off(), and adc_power_off_async().

Here is the caller graph for this function:

◆ adc_is_power_on()

bool adc_is_power_on ( uint32_t adc )

Is the ADC powered up and ready?

See also: adc_power_on_async

Parameters

adc	ADC Block register address base ADC register base addresses

Returns: true if adc is ready for use

Definition at line 84 of file adc_common_v2.c.

References ADC_ISR, and ADC_ISR_ADRDY.

Referenced by adc_power_on().

Here is the caller graph for this function:

◆ adc_power_off()

void adc_power_off ( uint32_t adc )

Turn off the ADC This will actually block if it needs to turn off a currently running conversion, as per ref man.

See also: adc_power_off_async

Parameters

adc	ADC Block register address base ADC register base addresses

Definition at line 144 of file adc_common_v2.c.

References adc_is_power_off(), and adc_power_off_async().

Here is the call graph for this function:

◆ adc_power_off_async()

void adc_power_off_async ( uint32_t adc )

Turn off the ADC (async) This will actually block if it needs to turn off a currently running conversion, as per ref man.

(Handles injected on hardware that supports injected conversions.

See also: adc_wait_power_off

Parameters

adc	ADC Block register address base ADC register base addresses

Definition at line 108 of file adc_common_v2.c.

References ADC_CR, ADC_CR_ADDIS, ADC_CR_ADSTART, ADC_CR_ADSTP, and adc_is_power_off().

Referenced by adc_power_off().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ adc_power_on()

void adc_power_on ( uint32_t adc )

Turn on the ADC.

See also: adc_power_on_async

Parameters

adc	ADC Block register address base ADC register base addresses

Definition at line 94 of file adc_common_v2.c.

References adc_is_power_on(), and adc_power_on_async().

Here is the call graph for this function:

◆ adc_power_on_async()

void adc_power_on_async ( uint32_t adc )

Turn on the ADC (async)

See also: adc_wait_power_on

Parameters

adc	ADC Block register address base ADC register base addresses

Definition at line 73 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADEN.

Referenced by adc_power_on().

Here is the caller graph for this function:

◆ adc_read_regular()

uint32_t adc_read_regular ( uint32_t adc )

ADC Read from the Regular Conversion Result Register.

The result read back is 12 bits, right or left aligned within the first 16 bits.

Parameters

[in] adc Unsigned int32. ADC block register address base ADC register base addresses

Returns: Unsigned int32 conversion result.

Definition at line 331 of file adc_common_v2.c.

References ADC_DR.

◆ adc_set_continuous_conversion_mode()

void adc_set_continuous_conversion_mode ( uint32_t adc )

Enable Continuous Conversion Mode In this mode the ADC starts a new conversion of a single channel or a channel group immediately following completion of the previous channel group conversion.

Parameters

[in] adc ADC block register address base ADC register base addresses

Definition at line 189 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_CONT.

◆ adc_set_left_aligned()

void adc_set_left_aligned ( uint32_t adc )

ADC Set the Data as Left Aligned.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 223 of file adc_common_v2.c.

References ADC_CFGR1, and ADC_CFGR1_ALIGN.

◆ adc_set_regular_sequence()

void adc_set_regular_sequence	(	uint32_t	adc,
		uint8_t	length,
		uint8_t	channel[]
	)

ADC Set a Regular Channel Conversion Sequence.

Define a sequence of channels to be converted as a regular group with a length from 1 to 18 channels. If this is called during conversion, the current conversion is reset and conversion begins again with the newly defined group.

Warning: This core doesn't support the random order of ADC conversions. The channel list must be ordered by channel number.

Parameters

[in]	adc	Unsigned int32. ADC base address (ADC register base addresses)
[in]	length	Unsigned int8. Number of channels in the group.
[in]	channel	Unsigned int8[]. Set of channels to convert, integers 0..18.

Definition at line 331 of file adc.c.

References ADC_CFGR1, ADC_CFGR1_SCANDIR, ADC_CHSELR, and cm3_assert_not_reached.

◆ adc_set_resolution()

void adc_set_resolution	(	uint32_t	adc,
		uint16_t	resolution
	)

ADC Set Resolution.

ADC Resolution can be reduced from 12 bits to 10, 8 or 6 bits for a corresponding reduction in conversion time.

Parameters

[in]	adc	Unsigned int32. ADC base address (ADC register base addresses)
[in]	resolution	Unsigned int16. Resolution value (ADC resolutions)

Definition at line 214 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_set_right_aligned()

void adc_set_right_aligned ( uint32_t adc )

ADC Set the Data as Right Aligned.

Parameters

[in] adc Unsigned int32. ADC base address (ADC register base addresses)

Definition at line 232 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_set_sample_time_on_all_channels()

void adc_set_sample_time_on_all_channels	(	uint32_t	adc,
		uint8_t	time
	)

ADC Set the Sample Time for All Channels.

The sampling time can be selected in ADC clock cycles from 1.5 to 239.5, same for all channels.

Parameters

[in]	adc	Unsigned int32. ADC base address (ADC register base addresses)
[in]	time	Unsigned int8. Sampling time selection (ADC sampling time)

Definition at line 375 of file adc.c.

References ADC_SMPR, and ADC_SMPR_SMP.

◆ adc_set_single_conversion_mode()

void adc_set_single_conversion_mode ( uint32_t adc )

Enable Single Conversion Mode In this mode the ADC performs a conversion of one channel or a channel group and stops.

Parameters

[in] adc ADC block register address base ADC register base addresses

Definition at line 201 of file adc_common_v2.c.

References ADC_CFGR1.

◆ adc_start_conversion_regular()

void adc_start_conversion_regular ( uint32_t adc )

ADC Software Triggered Conversion on Regular Channels.

This starts conversion on a set of defined regular channels. Depending on the configuration bits EXTEN, a conversion will start immediately (software trigger configuration) or once a regular hardware trigger event occurs (hardware trigger configuration)

Parameters

[in] adc ADC block register address base ADC register base addresses

Definition at line 386 of file adc_common_v2.c.

References ADC_CR, and ADC_CR_ADSTART.

Modules

Functions

Detailed Description

Function Documentation

◆ adc_calibrate()

◆ adc_calibrate_async()

◆ adc_clear_overrun_flag()

◆ adc_disable_delayed_conversion_mode()

◆ adc_disable_dma()

◆ adc_disable_dma_circular_mode()

◆ adc_disable_eoc_interrupt()

◆ adc_disable_overrun_interrupt()

◆ adc_disable_temperature_sensor()

◆ adc_disable_vrefint()

◆ adc_enable_delayed_conversion_mode()

◆ adc_enable_dma()

◆ adc_enable_dma_circular_mode()

◆ adc_enable_eoc_interrupt()

◆ adc_enable_overrun_interrupt()

◆ adc_enable_temperature_sensor()

◆ adc_enable_vrefint()

◆ adc_eoc()

◆ adc_eos()

◆ adc_get_overrun_flag()

◆ adc_is_calibrating()

◆ adc_is_power_off()

◆ adc_is_power_on()

◆ adc_power_off()

◆ adc_power_off_async()

◆ adc_power_on()

◆ adc_power_on_async()

◆ adc_read_regular()

◆ adc_set_continuous_conversion_mode()

◆ adc_set_left_aligned()

◆ adc_set_regular_sequence()

◆ adc_set_resolution()

◆ adc_set_right_aligned()

◆ adc_set_sample_time_on_all_channels()

◆ adc_set_single_conversion_mode()

◆ adc_start_conversion_regular()